From d3da45024ca600708e3ef44fca60f8aef933c61a Mon Sep 17 00:00:00 2001
From: ploopyco <54917504+ploopyco@users.noreply.github.com>
Date: Mon, 25 Nov 2019 17:50:05 -0500
Subject: [PATCH] Updated 4. Final assembly (markdown)

---
 4.-Final-assembly.md | 18 ++++++++++++++++--
 1 file changed, 16 insertions(+), 2 deletions(-)

diff --git a/4.-Final-assembly.md b/4.-Final-assembly.md
index f7bcff3..0d6da05 100644
--- a/4.-Final-assembly.md
+++ b/4.-Final-assembly.md
@@ -17,8 +17,20 @@ In this section, you'll go over how to put the two halves of the enclosure toget
 ## Step 3: Put the top onto the base
 [![Ploopy Trackball Final Assembly YouTube Video](https://lh3.googleusercontent.com/pCK_OrN8liihaSrH5aFGFaO8p1wyzNk0m1vXkxIdAvlzxrKG-YOdHLz-Z3pFII0WMeOXBG5i6u4bKUZiLn9LpfTSFv7WwLusvEyG-CzcCXDsmvmifr1boPnBuz5LJeru3DLe4GtltQ_9LgAH17jkrYZAzp_mveubstp_sx45ecqAq6B7l4ZUvkPtHN6CXfg54p3nqcFDoa_Dy6iCjy65ZZptgRkxAkZw9v3pbXT2pwKyas58wieT-iTXmfzbQw7X2km7I5yllyMY-Fhr4oOTia2-XNjXjePcaV-ekT-ePFudMakbEKUKbihFNESPX5zqSK87Aj1qjOnfoFA4DGtpgwdtNlAANF1xV5yNNavs1bg9AC5KWrZEK9pY8-64jXsEyPd2z-u-AoBnyIaKQzlvd7kgf-L9Bvb14PCd1bjtxKcDVx1YTP3Uh_feHjrd01xz1gTQQ_Ik3uLET1R8VNAEQQoeQrt7JTmXFXz58_TgJ6ZCcrFvSxaNlQDUwQfDcLOwpmqhx1pVBFUvOUE-YN5pcMm_QLMSSl0vLptOn80AjPTljgbwAZxbM2sSCyxKybm-f94v8myJb1SikyFGmBTSMIKh8KBokNRVw_8czMOTuL2w6Q_7HYH-W7VqinDDDoX8kohDEdi69S9zDwy_wyvezsNH4Yt7hEVsYylN1tkYvD6sidnR2FY-cpITUwxo5seqTp-mnfMZh9g2VxZUfgqW4wmCd-k-6JoRUXKMBKM9649O3C0=w1130-h753-no)](https://www.youtube.com/watch?v=l6ZIF_83VuQ)
 
-- You might need to use a bit of force to get the two halves together.
-- After assembling, ensure that the wheel can spin freely. If it can't, disassemble and try again. Make sure that the pin for the wheel slots into the hole in the Top.
+To put the Top on:
+
+- Align the USB-B connector with the Top.
+- Put your thumb on the primary buttons and your index and middle finger on the secondary buttons, and depress the buttons gently. (They should click.)
+- Pull the Top (it will bend slightly) until the peg from the scroll wheel enters its sheath in the Top.
+- Press the Top into the Base with gentle but firm pressure until the two are seated together entirely.
+
+To remove:
+
+- Put your thumb on the primary buttons and your index and middle finger on the secondary buttons, and depress the buttons gently. (They should click.)
+- Lift the rear end of the Top until the scroll wheel peg slips out of its sheath in the Top.
+- Pull the Top off.
+
+See the video for an example of how to accomplish this.
 
 ## Step 4: Insert the screws into the base and apply the friction pads
 ![](https://lh3.googleusercontent.com/BPjsb6ve06zRUGCbNSzeDNk04lssJfnJcaqkROE7XBmiuNPzj4c-7z8sLM5TEHzfDXdt2rpZz1G2Un28b2-SesGHnMVJNvesj6k2iCZJepmYJDXl0-YrseGuGsxVQ6vnlcJf1MPihEVwNysR3RPbXMHnMudxf6T4yMuLwpnQytmp5zcANJ7H1Lmeb2vzYp_IEpGk8QWTl6MEwtsBd8oVKL3rBTLCylvQLKn6u7qH0molkdJqGw6P8icG9KAAw45IiblrTEw86R8WyYHqZnnK7aS_llj8wWfQHXXnjQaHgxckesXRMwdU8-zHZPLfiX27tWVLXkltj9zEkgYR_bpDQRmQLScLLYogXjgc02HFURhZgwvRVx-ng3I1BVC4oVAnQ4XgcZ9uBft0BHLoPQXizncqyUIP37D-1-tTnY5nrO3uSTjDYScyy0I3R14a6Yuenfqy3lmQEZIbhobmJR6bRas_sNvNVwBdUhCpYysT73iRFp96WXHlK9i2k45QHLSNGjp2ptk08A4rqGXO972u_30gc4ulLf4Bi9x3Kq0MHJyRW_cWHAGdtwllVLZ0lwnGrLiTWerW4vjNskuZZ53j2JE5sF8C3xC9QW21dElNKWV8VzbmokGY2-Snpj4BH3B8paGNproVeGMT0M-WFHxmhZLpLaPdE2hH7pI4eqsVq3YqNDIXeDGr6qyrb-hFWkppYs3Ct4sGYaRqDQ3b_KwOjpGWFCS0LgKJxSlNh_XO0L59yQ0=w1454-h969-no)
@@ -33,6 +45,8 @@ Depending on slight size variations, you might need to push the ball in with som
 ## Step 6: Verify that the Ploopy Trackball is working correctly
 Plug the trackball into your computer. The buttons should be clicking, and if you move the ball, it should move the cursor.
 
+If the buttons are stuck, take the top off and adjust the primary and secondary buttons by rotating them slightly in their bases and trying again.
+
 ## Step 7: All done!
 Congrats, you finished building the Ploopy Trackball!